The outlet has a USB charger built in. Can that fail?

Yes — USB-integrated outlets contain switching electronics that can fail without affecting the outlet's mains pins. Sometimes you'll find the USB ports dead but the mains pins still work, or vice versa. Either way, the unit needs replacement.

Could it be a tripped circuit somewhere outside?

In rare cases, yes — particularly in homes with a meter board distinct from the main switchboard, or where outdoor circuits feed into indoor outlets. We can trace the circuit topology if standard switchboard checks don't reveal the cause.

Are old outlets actually unsafe or just unreliable?

Both, eventually. The pin-contact spring weakens, terminals loosen, plastics yellow and crack. An outlet 25+ years old is a planned replacement waiting to happen, particularly in coastal Sydney homes where salt accelerates the wear.

How quickly can you respond?

Non-urgent dead outlets are typically attended within 24 hours. Outlets with burning smell, heat, or sparking get 30–90 minute emergency response. Call 0433 462 902.

Can I fix a dead power point myself, or do I legally need an electrician in NSW?

In NSW, all electrical wiring work — including replacing or repairing an outlet — must be carried out by a licensed electrician; DIY repairs are illegal and can void your home insurance. The only safe checks you can do yourself are resetting a tripped RCD or breaker at the switchboard and testing a different appliance in the outlet.

How much does it cost to fix a dead power point in Sydney?

The cost varies depending on the underlying fault — an RCD reset takes minutes, while a loose loop connection or damaged wiring behind the wall requires more labour. Ask for a fixed-price quote before any work starts so there are no surprises on the bill.

What's the difference between an RCD and a circuit breaker, and which one trips when a power point dies?

A circuit breaker trips when a circuit is overloaded or short-circuits, protecting the wiring; an RCD (residual current device) trips the moment it detects current leaking to earth, protecting people from electric shock. Either can kill an outlet, but if only one or two points on the same circuit are dead while others are fine, an RCD trip is the more likely culprit.

Who do I call about a dead power point in a rental property — my landlord or an electrician?

Your landlord is legally responsible for maintaining safe electrical installations, so report the fault to them in writing straight away. If the outlet is sparking, smells burnt, or you suspect an urgent safety risk, call 0433 462 902 directly and notify your landlord at the same time — tenant safety comes first.

Should I worry if my power point has scorch marks or black discoloration around it?

Yes — scorch marks or black discoloration are a serious sign of arcing or overheating, not just cosmetic wear. Stop using that outlet immediately and have a licensed electrician inspect it as soon as possible, because sustained arcing inside a wall cavity is a known cause of house fires.

Power Point Not Working Artarmon

Emergency Response in Artarmon

Licensed electrician dispatched fast · 24/7 · 30–60 min

0433 462 902 Book Online

24/7 Emergency Response Licensed & Insured 30–60 Min Arrival Upfront Pricing

From Mosman and Neutral Bay through Lane Cove and out to Wahroonga and Hornsby, North Shore electrical systems share a common challenge: the largest residential properties in metropolitan Sydney supplied by overhead consumer mains running through some of its densest tree canopy.

On the leafy North Shore, a dead power point often shows up after EV chargers, home offices and data gear pile onto circuits never sized for them. Around Chatswood's strata towers it can be a shared-board issue, so we sort whether it's your socket or the building's supply.

⚠ Stop — Call Immediately if You Notice Any of These:

A burning, plastic, or fishy smell from the outlet
Visible scorching, browning, or melting around the face
Black soot at the pin holes
The outlet is hot to touch
The outlet sparked or popped before it stopped working
Adjacent outlets on the same circuit are also affected
A tingle felt when touching the outlet face

Full guide: Why Is My Power Point Not Working? — causes, FAQs & expert advice

About Why Is My Power Point Not Working?

A dead power point is most often caused by a tripped RCD, a tripped breaker, a loose loop connection behind the outlet, or worn pin contacts — not the outlet itself.

If the outlet sparked, smells burnt, or is hot to touch, call 0433 462 902 now; for a non-urgent fault, book a same-day diagnostic online.

In Sydney homes, an RCD reset incompletely and a damaged appliance drawing no current are two faults that often go unnoticed until an electrician checks the switchboard. Sydney Electrical Service is dispatched 24/7 across every metropolitan suburb, and diagnosis typically takes minutes once on site.

What to Do Right Now in Artarmon

Try a different appliance. Plug a known-working lamp or phone charger in.
Try the same appliance in a different outlet on a different circuit to confirm the appliance works.
Open the switchboard. Check for tripped breakers and RCDs.
Reset any tripped device once. If it won't hold, leave it OFF and call us.
Check the wall switch if the outlet has one — sometimes a switched outlet has been turned off without you noticing.
Inspect the outlet face for any damage, discolouration, or soot.
Touch-test the outlet for heat (gently — back of hand first).
Check adjacent outlets on the same circuit for any signs of damage.
Photograph any visible damage for our diagnostic dispatch.

Electrical work in Artarmon

Artarmon has a split personality that few North Shore suburbs share, a quiet, leafy grid of Federation homes and California bungalows on one side and one of Sydney's older light-industrial and commercial estates on the other. Many of the established houses still run the original two-wire wiring and small ceramic-fuse boards from their era, which simply weren't designed for today's appliances and need rewiring and a proper board upgrade with RCD protection. As an Ausgrid-accredited Level 2 team, that ageing residential stock is bread-and-butter work for us.

The industrial and commercial pocket around the station brings a different kind of job, larger loads, three-phase supply, sub-mains and tenancy fit-outs for warehouses, studios and trade businesses. We manage the network connection, consumer mains and metering for both sides of Artarmon, so whether it's a bungalow rewire or a workshop needing more power, the supply side is handled correctly and signed off.

Common Questions

The breaker isn't tripped but the outlet is dead. What's wrong?

A loose connection at the outlet itself, at an upstream outlet on the loop, or in the cable behind the wall. The breaker only trips on overcurrent, short, or earth leakage — not on a simple open circuit.

Why does the same outlet keep going dead?

The outlet itself is failing — most commonly worn pin contacts, a loose terminal, or a degraded back-stab termination. Replacing the outlet is straightforward and usually permanent.

Can I just plug into a different outlet?

For now, yes — but the dead outlet is a clue that something on the circuit isn't healthy. Loose terminations heat up. We recommend booking a diagnostic before the next failure.

How do I know if it's the appliance or the outlet?

Plug the appliance into a different outlet on a different circuit. If it still doesn't work, the appliance is the fault. If it works elsewhere, the outlet is the fault.

Why Artarmon Residents Choose Us

We've worked across every North Shore suburb from Cremorne through to Hornsby, and we know the multi-circuit complexity that typifies the region. Architectural multi-storey builds, Federation heritage residences, and harbour-side apartments each have characteristic switchboard challenges we arrive ready to handle.