Safety Switches

Book or quote your job

Licensed Level 2 ASP · 24/7 across Sydney

0433 462 902 Book Online

How it works

Safety switch installation, testing, and replacement covers the RCD (residual current device) protection required on power, lighting, and high-current circuits in Sydney homes and businesses. If your switchboard is missing RCDs, a switch has failed its test, or you're getting nuisance trips, call 0433 462 902 or book online. We retrofit RCDs to unprotected circuits on older boards, replace failed or aged devices, and diagnose nuisance tripping caused by degraded insulation or faulty appliances. As a licensed Level 2 ASP working across the Ausgrid network, we can also carry out any associated metering or service line work and issue the required compliance certificates under a single visit.

What's Involved

A safety switch installation or upgrade in Sydney typically includes:

Site inspection — checking which circuits already have RCD protection, identifying any disabled or seized RCDs, testing trip current and trip time on existing devices
RCD installation on every unprotected final subcircuit — lighting, power, oven, hot water, air conditioning, pool equipment
Type AC versus Type A versus Type B selection — Type A is now required where switch-mode appliances (EVs, induction cooktops, modern A/C) are connected
Earth fault loop impedance testing on every circuit before re-energisation
RCD operating-time verification — we measure the actual trip time at rated trip current and document the result
Labelling and homeowner walk-through — we show you how to test every RCD on your board and what to do if one trips

Where the switchboard is too small to accept new RCDs, we recommend a full switchboard upgrade rather than over-stuffing the existing board.

NSW Compliance

RCD requirements in NSW are set by:

AS/NZS 3000:2018 — every final subcircuit in a new installation or upgrade requires RCD protection
AS/NZS 3017 — RCD trip-time and trip-current verification, documented per circuit
NSW Service and Installation Rules — RCD selection where switch-mode loads are connected (Type A or Type B)

Our credentials:

NSW electrical contractor licence
Level 2 ASP accreditation
$20 million public liability insurance

Every safety switch installation we complete is issued with a Certificate of Compliance for Electrical Work (CCEW) lodged with NSW Fair Trading. We keep your test results on file for seven years and can re-supply them for insurance or strata records on request.

Pricing Approach

Safety switch pricing in Sydney depends on:

How many circuits need protection — older boards may have 4–6 unprotected circuits; we price per device
RCD type required — Type AC (cheapest), Type A (most common today), Type B (for EV chargers, large solar inverters)
Whether the existing switchboard has room — if not, the more cost-effective option is a full switchboard upgrade with all-new RCD/MCB combo devices

A single Type A RCD retrofitted to an existing circuit on a switchboard with space typically runs $250–$380 installed and certified. A full board of 6–8 RCD/MCB combo replacements with new labelling and test report runs $1,400–$2,200. We quote on inspection; nothing is added later.

Frequently Asked Questions

What does safety switch (RCD) installation actually involve?

Safety switch installation means fitting an RCD to your switchboard to protect power, lighting, or high-current circuits — the device monitors current flow and cuts power within milliseconds if a fault is detected. The work includes selecting the correct RCD type and rating for each circuit, installing it inside the switchboard, and testing it to confirm it trips within the limits required by AS/NZS 3000.

Do I really need a safety switch on every circuit in my home?

Yes — under the current Australian wiring rules (AS/NZS 3000), RCD protection is mandatory on all power and lighting circuits in new installations and significant upgrades. Many older Sydney homes have a safety switch only on power points, or none at all, leaving lighting circuits and hardwired appliances completely unprotected.

Is a licensed electrician required to install or replace a safety switch?

Yes — safety switch installation is licensed electrical work in NSW and cannot legally be carried out by a homeowner or handyman. Once the work is done, your electrician must issue a Certificate of Compliance for Electrical Work (CCEW), which is your written proof the installation meets the required standard.

How do I know if my switchboard is missing safety switches?

Open your switchboard and look for devices labelled RCD or marked with a small test button — if your circuits are protected only by circuit breakers or old ceramic fuses with no test button, you have no RCD protection. An older fuse board in a pre-1990s Sydney home almost certainly has none, and a licensed electrician can confirm exactly which circuits are exposed.

Can I test my own safety switch, or do I need an electrician?

You can — and should — press the TEST button on your RCD every three months to confirm it trips correctly; this is a simple check any homeowner can do. If the switch fails to trip, won't reset, or keeps nuisance-tripping without a clear cause, call a licensed electrician to diagnose the fault rather than leaving the circuit unprotected.

How long does safety switch installation or replacement take?

Retrofitting RCDs to an existing residential switchboard typically takes two to four hours, depending on the number of circuits and the condition of the board. Replacing a single failed safety switch is usually completed within an hour.

How much does safety switch installation cost?

Cost varies based on the number of circuits needing protection, your switchboard type, and whether any rewiring is required — so we always provide a fixed-price quote before starting work. Call 0433 462 902 or book online to get an accurate price for your specific property.

Is it worth upgrading an older switchboard just to add safety switches?

Yes — an RCD can cut power in as little as 30 milliseconds, fast enough to prevent a fatal electric shock, making it one of the highest-value safety upgrades available for an older Sydney home. RCD protection is also a compliance requirement before certain electrical work can be certified, so upgrading now avoids complications and extra cost later.