Will replacing the RCD fix the problem?

Only if the RCD itself has failed. If the fault is in the wiring or an appliance, a new RCD will simply trip just like the old one. Diagnosis first, replacement second.

Why does my RCD trip when I plug something into a particular outlet?

The outlet itself may have damaged insulation, water ingress, or a damaged conductor inside the wall. We've found everything from screws driven into cables to rodent-damaged cores. Stop using the outlet and have it tested.

Do older Sydney homes need an RCD upgrade?

If your switchboard pre-dates 2000, the answer is almost certainly yes. Most pre-2000 boards have at most one RCD covering only a couple of circuits. Modern AS/NZS 3000 requires RCD protection on all final subcircuits — including lighting.

How long does an RCD last?

A well-installed RCD typically lasts 10–15 years. Coastal exposure (the Eastern Beaches, Northern Beaches, Sutherland Shire) can shorten that significantly due to salt-air corrosion of the contacts.

Is it safe to keep resetting my RCD if it keeps tripping back?

No — each reset into an active fault re-exposes you to the exact danger the RCD is designed to stop. If it trips a second time, stop resetting and treat that circuit as unsafe until a licensed electrician finds and fixes the underlying cause.

Should I worry if my RCD trips once but doesn't trip again?

Yes — a single trip still means a real earth leakage event occurred, and the fault is likely intermittent rather than gone. Moisture that dries out or an appliance that only leaks under certain load conditions can disappear and return, so have a licensed electrician run a diagnostic before the next trip catches you off guard.

Will my house catch fire if my RCD keeps tripping?

A tripping RCD is actually doing its job — but the underlying fault causing it can worsen over time, and degraded wiring insulation can eventually reach the point where arcing or overheating becomes a genuine fire risk. Treat repeated trips as an urgent warning, not a nuisance to reset away.

How much does it cost to diagnose an RCD fault in Sydney?

Cost varies depending on how many circuits need to be tested and the complexity of the fault — call 0433 462 902 for a fixed-price diagnostic quote before any work begins. Sydney Electrical Service provides upfront pricing with no hidden callout surprises across Sydney.

What's the difference between an RCD tripping and a circuit breaker tripping?

An RCD trips in response to earth leakage — current escaping outside its normal path, which is a direct shock and electrocution risk. A circuit breaker trips on overload or short circuit — too much current in the circuit — so the two devices protect against different dangers, and diagnosing one fault is not the same as diagnosing the other.

RCD Tripping Leichhardt

Emergency Response in Leichhardt

Licensed electrician dispatched fast · 24/7 · 30–60 min

0433 462 902 Book Online

24/7 Emergency Response Licensed & Insured 30–60 Min Arrival Upfront Pricing

Strathfield, Burwood, and Concord post-war brick veneers face their own electrical challenges — three-phase legacy supply, oversized backyards with detached structures (granny flats, sheds, studios), and original aluminium wiring developing oxide-related hotspots.

A constantly tripping RCD in an Inner West Federation terrace usually points back to ageing rubber or two-wire wiring that leaks to earth as it perishes. Across Newtown, Marrickville and Annandale, decades of partial DIY additions and damp old walls make these nuisance trips a regular call for us.

⚠ Stop — Call Immediately if You Notice Any of These:

A tingle, prickle, or buzz when you touch a tap, appliance, or shower fitting
A burning, fishy, or "electrical" smell anywhere on the affected circuit
Hot or discoloured power points on the affected circuit
An RCD that holds for a few seconds then trips — strongly suggests a real, active leakage
An RCD that won't trip when its TEST button is pressed — the device itself has failed

Full guide: Why Is My RCD Tripping? — causes, FAQs & expert advice

About Why Is My RCD Tripping?

RCD tripping is caused by earth leakage — most often a faulty appliance, moisture inside a fitting or cable, degraded wiring insulation, or cumulative leakage across shared circuits. If tripping repeats or returns after resetting, you have an active fault that can cause electrocution or fire; call 0433 462 902 or book a diagnostic before resetting again. Every trip must be treated as real: RCDs are the single most important shock-protection device in your switchboard.

Sydney Electrical Service handles RCD diagnostics 24/7 across every Sydney suburb — from older Federation cottages in Marrickville and Annandale to high-rise strata in Pyrmont and Zetland. Northern Beaches outdoor entertaining areas face accelerated insulation breakdown from salt air and weather, making them a frequent source of hard-to-trace earth leakage.

What to Do Right Now in Leichhardt

Open the switchboard. Find the tripped RCD (the toggle will be in the middle position, or fully OFF).
Switch every breaker downstream of that RCD to OFF.
Reset the RCD to ON. It should now hold because no circuits are live.
Switch breakers back on one at a time with a 30-second pause between each.
The breaker that re-trips the RCD is the faulty circuit.
Unplug everything on that circuit and try again.
If the RCD holds, plug appliances back in one at a time to find the offender.
If it doesn't hold with everything unplugged, the fault is in the fixed wiring or a hardwired appliance — leave it OFF and call us.

Electrical work in Leichhardt

Leichhardt's housing tells the suburb's story, from tightly packed Victorian terraces and humble workers' cottages through to converted warehouses and former industrial buildings now living as homes and studios. It's a suburb that has been renovated hard over the decades, which means we often open up a wall and find a patchwork of old and newer wiring, junctions hidden behind plaster, and switchboards that have been added to one circuit at a time rather than planned. Ausgrid runs the local network, and as an accredited Level 2 ASP we look after the connection from the street to your board.

Typical work here includes safety-driven rewires, consolidating those messy boards into a single compliant switchboard with RCD protection, and lifting undersized consumer mains to suit modern living. Warehouse-style conversions frequently call for three-phase supply and proper sub-mains. We also handle defect rectification, metering and overhead or underground service upgrades through Ausgrid.

Common Questions

What's the difference between an RCD and a safety switch?

None — they are the same device. "Safety switch" is the colloquial Australian name for what AS/NZS 3000 calls a Residual Current Device.

What is "nuisance tripping"?

Nuisance tripping is when an RCD trips without an obvious dangerous fault — usually because cumulative low-level leakage from several healthy appliances on one bank exceeds the 30 mA threshold. The fix is splitting circuits across more RCDs (RCBOs).

Should I test my RCD myself?

Yes — press the TEST button every three months. If the device does not trip, it has failed and must be replaced immediately. AS/NZS 3760 recommends three-monthly testing for residential installations.

My RCD trips when I switch on the dishwasher (or kettle, dryer, washing machine). Is the appliance dead?

Likely yes. The internal element insulation has degraded enough to leak to the metal body. Even if the appliance still "works," it is no longer safe to use until the element is replaced or the unit is retired.

Why Leichhardt Residents Choose Us

Pre-1995 ceramic-fuse boards still in service are over-represented in our Inner West callouts. We complete switchboard upgrades from fuse-board legacy to per-circuit RCBO protection in single-day jobs across the region.