Why are some Sydney homes so short of wall outlets?

Older homes were wired for an era of three or four electrical appliances. A modern household can have 30+ devices on standby alone. We add fixed outlets routinely as part of renovation work — often the safest, cheapest long-term solution.

Can I use an outdoor power board outdoors?

Only if it is specifically rated for outdoor use (IP rating, weatherproof) and used within its rating. Most standard indoor boards used outdoors are a fire and electrocution risk, particularly during Sydney storms.

Are USB-charging power boards safer?

Not necessarily — USB-charging boards add internal switching electronics that introduce their own failure modes. Quality of the charging circuit varies dramatically by brand. Compliant Australian-marked boards from reputable brands are the safer choice.

How quickly can you respond?

Routine non-urgent power board issues are typically attended within 24 hours. If the wall outlet behind the board is hot or scorched, response is 30–90 minutes. Call 0433 462 902.

Will my house catch fire if I plug too many things into one power board?

It is a genuine risk, not just a scare — overloaded power boards are among the leading causes of house fires across NSW. High-draw appliances like portable heaters, air fryers, and kettles can push a board well past its rated amperage, causing the wiring to overheat long before any safety device trips. If your home is short on wall outlets and you are relying on a heavily loaded board, have a licensed electrician assess your circuits.

Can I plug one power board into another to get more outlets?

No — daisy-chaining power boards is dangerous and does not comply with Australian electrical standards (AS/NZS 3000). Stacking boards concentrates heat at the connection point and bypasses the current rating each board was designed around, creating a serious fire hazard. The correct fix is additional wall outlets installed by a licensed electrician.

What is the difference between my power board tripping and my circuit breaker tripping?

A power board trip — via its reset button or internal fuse — cuts power to the board only, while a circuit breaker trip at your switchboard kills an entire circuit in your home. If your circuit breaker keeps tripping after you reset it, the problem is deeper than the power board itself and points to a wiring or load issue that needs a licensed electrician to diagnose safely.

Should I worry if my power board feels warm to the touch?

Yes — switch it off at the wall immediately if it is hot, discoloured, or smells of burning plastic. A slight warmth under moderate load can be normal, but genuine heat is a sign of a failing internal connection or chronic overload. Do not keep using it; replace the board and, if the wall outlet behind it is also warm, call 0433 462 902 for an urgent inspection.

How much does it cost to have extra wall outlets installed in my Sydney home?

Cost varies depending on the number of outlets, wall construction, and how far new wiring needs to run — so there is no single figure that applies to every job. Sydney Electrical Service provides fixed-price quotes, so you know the full cost before any work begins.

Power Board Not Working Lane Cove

Emergency Response in Lane Cove

Licensed electrician dispatched fast · 24/7 · 30–60 min

0433 462 902 Book Online

24/7 Emergency Response Licensed & Insured 30–60 Min Arrival Upfront Pricing

Tree-heavy suburbs — Wahroonga, Killara, Pymble, Hunters Hill, Lane Cove — see the highest rate of overhead consumer mains damage in metro Sydney. East-coast lows and storm-driven branches account for hundreds of point-of-attachment and service-mains callouts every storm season.

On the North Shore the bigger leafy homes and Chatswood strata towers are stacking on EV chargers, data cabinets and home automation, which pushes original boards past their limit. A power board that's tripping or dead up here is often an overloaded board that needs proper RCBOs and a capacity upgrade.

⚠ Stop — Call Immediately if You Notice Any of These:

A burning, plastic, or fishy smell from the board
Visible scorching, browning, or melting on the board
The board is hot to touch
The cord is hot or has visible damage
A spark or pop occurred when something was plugged in
The board buzzes or crackles
Smoke from any direction near the board
The wall outlet feeding it is hot or smells

Full guide: Why Is My Power Board Not Working? — causes, FAQs & expert advice

About Why Is My Power Board Not Working?

A dead power board is most commonly caused by a blown internal fuse, an exhausted surge-protector module, a failed rocker switch, or a faulty wall outlet feeding it. If the outlet behind the board feels hot or smells burnt, that is a fire risk — book an urgent inspection or call 0433 462 902 now.

Sydney homes — particularly pre-1990s dwellings — were wired with far fewer outlets than modern living demands, which is why power boards are routinely run harder than they were designed for. Running multiple high-current appliances — heaters, kettles, hairdryers, toasters — through a single board for sustained periods overloads the strip and stresses the outlet behind it. Sydney Electrical Service operates 24/7 across every metropolitan suburb and can diagnose whether the fault lies in the board, the outlet, or the circuit.

What to Do Right Now in Lane Cove

Try a different appliance in the board to confirm the board is dead, not the appliance.
Check the on/off switch if the board has one. Some boards have illuminated switches that fail.
Look for an overload reset button — a small button on the side or end of the board.
Try the wall outlet directly with a known-working appliance.
If the wall outlet is also dead, see Why is my power point not working?.
Check the board's surge protection indicator if fitted — typically green/red.
Inspect the cord for cuts, abrasions, or kinks.
Check for liquid contamination or visible internal damage.
If the wall outlet is hot or scorched, isolate the breaker and call us.

Electrical work in Lane Cove

Lane Cove has a real mix — mid-century brick homes and post-war cottages on the bushland fringe, a heavy concentration of 1960s and 70s walk-up strata flats around the town centre, and newer apartment buildings closer to the village. The bushland and Lane Cove River setting is lovely but the older flat blocks tend to share tired common-area switchboards, ageing sub-mains and metering that hasn't kept pace with how people use power today.

For the older red-brick units we handle strata switchboard upgrades, RCD installation and rewiring of common circuits. In the freestanding homes we see undersized boards, mixed-vintage wiring and not enough capacity for renovations. Bigger family homes on the larger blocks often warrant a three-phase upgrade, which is Level 2 work — new consumer mains, point-of-attachment and the network connection coordinated with Ausgrid. Bushland proximity also makes solid earthing and surge protection worthwhile here.

Common Questions

Should I open the power board to fix it?

No. Power boards are not designed to be opened or serviced. Once a board has failed, dispose of it (e.g. via your local Sydney council e-waste service) and replace with a new unit.

How do I know if a power board is overloaded?

Add up the wattage of everything plugged in. A standard 10 A board is rated for 2,400 W maximum and most cheap boards should be operated well below that. A heater (2,000 W) and a kettle (2,400 W) on the same board exceeds the rating immediately.

Why does my surge-protected board not protect anymore?

Surge protectors have a finite energy capacity. Each surge they absorb degrades them slightly; eventually they reach end of life and the indicator light goes from green to red. After that, the board still distributes power but offers no protection.

Is it OK to leave a power board on permanently?

Modern compliant boards rated for the load are generally fine for sustained use. Cheap or aged boards with high-current appliances are not. If your power board is hot during normal use, replace it.

Why Lane Cove Residents Choose Us

Tree-canopy storm damage accounts for around a quarter of our North Shore emergency callouts. We coordinate with arborists, Ausgrid, and roof tradespeople routinely for the multi-trade jobs that follow major storm events in Wahroonga, Killara, Pymble, and Hunters Hill.