Can possums damage outdoor lights?

Yes — possums and bats both nest in eaves and roof cavities, and chewing damage on cabling is one of the most common Sydney causes of outdoor light failure. We see this constantly in older Inner West, North Shore, and Hills District homes.

Are LED retrofits OK in my old halogen outdoor fittings?

Sometimes — but the fitting must be LED-compatible (no transformer, or LED-rated transformer) and the IP rating must be preserved. We see retrofits that compromise the seal and lead to failure within 12 months.

My pool light doesn't work — is this the same problem?

Pool lights have stricter zoning rules under AS/NZS 3000 because they sit in or near water. They are typically 12 V or 24 V SELV (Separated Extra-Low Voltage) and require a specific transformer and earth strategy. We attend pool-light callouts as a specialised job.

How quickly can you respond?

We dispatch 24/7 across all Sydney suburbs. Outdoor lighting faults without active fire/shock risk are typically attended within 24 hours; faults with smoke, sparks, or hot fittings get 30–90 minute emergency response. Call 0433 462 902.

Do I really need a licensed electrician to replace an outdoor light fitting, or can I do it myself?

Yes — in NSW, replacing a light fitting is defined electrical work that legally requires a licensed electrician; doing it yourself is illegal, can void your home insurance, and risks a serious shock. The only things a homeowner can safely do are replacing a bulb or resetting a tripped RCD.

Should I worry if my outdoor light fitting has scorch marks or smells like burning?

Turn the circuit off at the switchboard immediately — scorch marks or a burning smell mean the fitting has overheated and is a genuine fire risk. Don't use the light again until a licensed electrician has inspected the fitting and the cable behind it.

How much does it cost to fix outdoor lights in Sydney?

The cost varies depending on how many fittings are affected, the condition of the cabling, and how easy the access is — call 0433 462 902 and we'll give you a fixed-price quote before any work starts, with no hidden call-out surprises.

My RCD keeps tripping every time it rains — is that a big deal?

It's a serious fault, not a nuisance quirk. Rain-triggered RCD trips almost always mean water is entering a fitting or a cracked cable sheath is creating a leakage current to earth — exactly the shock and fire hazard the RCD is protecting you from. Get it diagnosed before the next downpour.

What does the IP rating on an outdoor light mean, and does it matter in Sydney?

The IP (Ingress Protection) number tells you how well a fitting resists water and dust — IP44 is the minimum for covered outdoor areas, but IP65 or higher is strongly recommended for exposed positions. In Sydney's coastal suburbs like Bondi, Coogee, and Manly, salt-laden air can destroy a poorly rated fitting within a year or two, so choosing the right IP rating at installation saves a costly early replacement.

Outdoor Lights Not Working Sans Souci

Emergency Response in Sans Souci

Licensed electrician dispatched fast · 24/7 · 30–60 min

0433 462 902 Book Online

24/7 Emergency Response Licensed & Insured 30–60 Min Arrival Upfront Pricing

⚠ Stop — Call Immediately if You Notice Any of These:

A burning smell from any outdoor fitting
Visible water dripping from a fitting
Soot, char, or melting on any fitting
Sparks visible from a fitting
A fitting that is hot to touch
Tingles from any outdoor metalwork — fence, rail, gate, BBQ
An RCD that trips when outdoor lights switch on
A buzzing or crackling sound from any fitting

Full guide: Why Are My Outdoor Lights Not Working? — causes, FAQs & expert advice

About Why Are My Outdoor Lights Not Working?

Outdoor lights fail most often because of a failed photocell or PIR sensor, water ingress into a fitting, a tripped RCD, or a perished cable. Water inside a fitting or a damaged cable is a genuine shock and fire hazard — if your lights are intermittent or your RCD keeps tripping, call 0433 462 902 immediately or book a same-day diagnostic.

Sydney’s coastal suburbs — Bondi, Coogee, Manly, Cronulla, Avalon — see salt-driven corrosion destroy fittings and cable sheaths years faster than inland properties. Outdoor circuits also run the longest cable runs in most homes, with the most intermittent switching and weatherproof seals to maintain, which is why they appear disproportionately in our Sydney callouts. Sydney Electrical Service is dispatched 24/7 across every metropolitan suburb.

What to Do Right Now in Sans Souci

Try the manual switch (if any) to confirm power is reaching the circuit.
Check the switchboard for tripped breakers or RCDs on outdoor circuits.
Reset any tripped device once. If it won't hold, leave it OFF and call us.
For sensor-controlled lights, cover the photocell to simulate darkness and see if lights activate.
For PIR motion lights, walk through the detection zone in low light to test.
Inspect each fitting visually (during daylight) for water, damage, soot, or insect ingress.
Try replacing the bulb in accessible fittings. LED retrofit bulbs need to match the fitting's voltage and driver.
Photograph any damaged fittings for our diagnostic dispatch.
For total circuit failure with no obvious bulb cause, book a Level 2 electrician.

Electrical work in Sans Souci

Tucked between Kogarah Bay and the Georges River, Sans Souci is one of those bayside St George pockets where the housing stock runs from modest mid-century cottages to large modern two-storey rebuilds taking advantage of the water views. Many of the larger new homes here are pulling far more load than the old single-phase supply was ever sized for, with ducted air, induction cooking, pool pumps and EV chargers all wanting power at once. That often means an upgrade to a three-phase supply and a larger consumer mains run to keep everything stable.

Being so close to the bay, the marine environment is the other big factor. Salt-laden air corrodes external switchboards, service cables and point-of-attachment hardware, so weatherproofing and regular checks of the outdoor gear really matter down here. Sans Souci is supplied through the Ausgrid network, and as an accredited Level 2 electrician we can carry out the network connection work, new metering, underground or overhead mains and storm-damage repairs, then bring the switchboard up to standard with modern RCDs and circuit protection.

Common Questions

Why don't my outdoor sensor lights come on at night anymore?

The most likely cause is a failed photocell or PIR sensor — both have finite service lives, particularly in coastal Sydney where salt air shortens them. Replacement is straightforward but requires a licensed electrician.

The lights work but the sensor doesn't activate. What's wrong?

The bulb is fine but the sensor has failed in the "always on" or "always off" position, depending on the model. Some sensors also have user-adjustable sensitivity and timeout that may have drifted. We can test, recalibrate, or replace as needed.

My outdoor lights stopped after the storm. Will they come back?

Sometimes — if the fault was transient water ingress that has dried out. More often, water has reached terminations and corrosion has begun. Inspecting fittings during daylight and replacing damaged seals is the right approach.

Why do my garden lights need a transformer?

Many low-voltage garden lights run on 12 V or 24 V for safety in the wet. The transformer steps mains 230 V down to the lower voltage. Transformers do fail — typically with a buzzing or hot housing and lights that flicker or cut out.